6440A REV J Norge Washer Parts List

Dryer cycling thermostat (dryer operating thermostat)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Bake element

This partially open-style bake element comes with ¼-inch push-on terminals and is located on the bottom of the oven. This bake element provides heat for baking. If your oven is too hot, not heating evenly, the element is not heating, or has little to no heat when baking, you may need to replace your bake element. You can use a multi meter to test the bake element for electrical continuity to see if you need to replace it. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

M series new style coil kit (sub 12001349)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Rear drum support roller kit (support)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Rear drum bearing kit (dryer rear drum bearing kit. The holes in the metal plate are not threaded. Use the self tapping screws in the kit to thread the plate.)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Crisper drawer cover (cover vegetable pan - wr32x10398)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.

Flat style oven igniter kit (igniter glowbar)

The flat style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, then your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter please be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3-3/4" in length and the amperage range is 3.3 to 3.6. The kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to the range wiring using porcelain wire nuts. This is a genuine OEM part.

Refrigerator ice and water filter (water filter - mwf)

Replacement ice maker (refrigerator ice maker)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Bake element - 220v 2300w (bake unit 208/240v)

This closed-hinged style bottom bake element is located on the bottom of the oven cavity to supply the heat for baking. This bake element has screw-on wire terminals is 18 1/4-inch wide and 14 1/2-inch deep to mounting flange and the terminal ends extend 2 1/2-inch past the flange. The element is 2300 watts and 20 volts. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Bake element - 240v (bake unit 208/240v)

This 240-volt 3100 watt bake element has screw style connections, 13 1/4-inch wide by 163/4-inch long. The bake element is located on the bottom of the oven cavity and supplies the heat for baking. If your oven is not heating evenly, the element will not heat or there is little to no heat when baking, you may need to replace the element. This genuine OEM bake element comes with an instruction sheet and is intended for use with electric ovens. Please remember to disconnect the power to your range before you start your repair.

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Dryer drum support roller

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.